 |
|
|
|
|
|
|
|
|
|
 |
 |
|
|||||||
 |
 |
 |
 |
 |
 |
 |
 |
|
|
|
VA 08 II VA 08 II Rescue and Tow Truck is designed for flexible action during rescue of vehicles resting off the public roads as a result of accidents, and for loading of the vehicles onto towing equipment if their axles or tyres are damaged.Vehicles which are only immobile (breakdown of engine, transmission, etc.) can be towed using a classical tow assembly located at the back of the truck. The truck has 40 and 50 mm pivot tows and respective tow bars.  Tab for crane works - Lifting capacity in tons - Tab for towing - Lifting capacity in tons TECHNICAL SPECIFICATION Chassis The tow superstructure is mounted on a Mercedes-Benz Actros 3346 chassis, wheelbase 5.100 mm. Chassis parameters: Wheelbase: 5100mm Rear axle wheelbase: 1350mm Width: 2482mm Cabin height (acc. to type): 3203- 3483mm Length: 8800mm Kerb weight: 22000kg Total weight: 33000kg Axle load capacity: 9000/13000/13000kg Engine output: 335kW Superstructure Superstructure technical parameters: Length: 6800mm Width: 2500mm Collapsed height: 3150 mm Max. height, extended boom: 6550 mm Telescope extension: 3500 mm Tow unit extension: 1700 mm Outrigger extension: 500 mm Superstructure weight: 9500-11000 kg Load capacity of max. extended telescope (horizontal): 6000 kg Load capacity of extended telescope (max. raise): 8000 kg Load capacity of retracted telescope (max. raise): 12000 kg Load capacity of tow assembly (max. extension): 7000 kg Load capacity of tow assembly (retracted): 10000 kg Load capacity of tow frame and jigs: 8000 and 10000 kg Winch tow capacity: 6000 kg The superstructure is fitted with three winches with a rope towing power of about 120 kN and rope length of 50 m. Two winches are located on the truck frame, and one on the main boom. The ropes of all winches are routed through rotating pulley blocks which facilitates winching of vehicles (or other handled objects) in a 180° sector at the rear of the truck. One winch can be used to stabilize the truck itself, while the rope of another winch can pull loads at an angle of up to 90° to the truck's longitudinal axis. To prevent rear of the truck from shifting rearwards (in the direction of the rope pull) 2 outriggers are used, which otherwise serve as stabilizers (also to take the load off the rear axles of the chassis) when lifting heavier loads with the winch located on the main boom. The third winch, located at the foot of the main boom, can be used to pull loads in the truck's axis at the rear, e.g. to load something onto the towing assembly; also loads up to 8 t can raised up to 5 m above the ground at a distance of about 2 m from the truck's rear end, with the telescopic boom section extended at about 3.5 m. The total length of the extended boom is approximately 8.8 m.    Superstructure Control All functions (working actions) of rescue and tow equipment VA-08 II can be controlled remotely using CALL 19 controller or by means of tilting switches on the control panel located on the right side of the truck. Storage Spaces VA-08 II truck has sufficient closed storage spaces for storing and fixing rescue and binding accessories. Recommended Equipment Binding and rescue accessories, fire-extinguishing equipment, hydraulic rescue equipment, towed truck light ramp, warning cones and other site marking equipment, welding unit with power generator, equipment for towing of trailer, set of towing forks with adapters. Accessories The vehicle is equipped with special accessories for rescue and towing work. Accessories are located in the right and left external boxes of the superstructure, as well as in several other storage spaces inside the superstructure. General use accessories: binding equipment - polyester binding slings 2 pcs - locking strut for boom 1 pcs Accessories for towing using a tow bar: - tow bar 2 pcs Accessories for towing using forks and tow frame: - towing forks 4 pairs - fork holder 2 pcs - towing frame L + R 2 pcs Rescue accessories: - pulley for doubling towing force and for winching vehicles 1+1 pc 
|